Data Portal @ linkeddatafragments.org

Matches in DBpedia 2014 for { <http://dbpedia.org/resource/SIMM> ?p ?o. }

• SIMM abstract "A SIMM, or single in-line memory module, is a type of memory module containing random access memory used in computers from the early 1980s to the late 1990s. It differs from a dual in-line memory module (DIMM), the most predominant form of memory module today, in that the contacts on a SIMM are redundant on both sides of the module. SIMMs were standardised under the JEDEC JESD-21C standard.Most early PC motherboards (8088-based PCs, XTs, and early ATs) used socketed DIP chips. With the introduction of 286-based IBM XT/286, which could use larger amounts of memory, memory modules evolved to save motherboard space and to ease memory expansion. Instead of plugging in eight or nine single DIP DRAM chips, only one additional memory module was needed to increase the memory of the computer. A few 286-based computers used (often non-standard) memory modules like SIPP memory (single in-line pin package). The SIPP's 30 pins often bent or broke during installation, which is why they were quickly replaced by SIMMs which used contact plates rather than pins.SIMMs were invented and patented by Wang Laboratories. Wang invented what was to become the basic memory module, now known as a SIMM (single in-line memory module) in 1983. The original memory modules were built upon ceramic and had pins. Later the pins were removed and the modules were built on standard PCB material.The first variant of SIMMs has 30 pins and provides 8 bits of data (plus a 9th error-detection bit in parity SIMMs). They were used in AT (286), 386, 486, Macintosh Plus, Macintosh II, Quadra, Atari STE and Wang VS systems.The second variant of SIMMs has 72 pins and provides 32 bits of data (36 bits in parity and ECC versions). These appeared first in the early 1990s in the IBM PS/2, and later in systems based on the 486, Pentium, Pentium Pro, early Pentium II, and contemporary/competing chips of other brands. By the mid 90s, 72-pin SIMMs had replaced 30-pin SIMMs in new-build computers, and were starting to themselves be replaced by DIMMs.Non-IBM PC computers such as UNIX workstations may use proprietary non-standard SIMMs. The Macintosh IIfx uses proprietary non-standard SIMMs with 64 pins.DRAM technologies used in SIMMs include FPM (Fast Page Mode Memory, used in all 30-pin and early 72-pin modules), and the higher-performance EDO DRAM (used in later 72-pin modules).Due to the differing data bus widths of the memory modules and some processors, sometimes several modules must be installed in identical pairs or in identical groups of four to fill a memory bank. The general rule of thumb is a 286, 386SX, 68000 or low-end 68020 / 68030 (e.g. Atari, Mac LC) system (using a 16 bit wide data bus) would require two 30-pin SIMMs for a memory bank. On 386DX, 486, and full-spec 68020 through 68060 (e.g. Amiga 4000, Mac II) systems (32 bit data bus), either four 30-pin SIMMs or one 72-pin SIMM are required for one memory bank. On Pentium systems (data bus width of 64 bits), two 72-pin SIMMs are required. However, some Pentium systems have support for a "half bank mode", in which the data bus would be shortened to only 32 bits to allow operation of a single SIMM. Conversely, some 386 and 486 systems use what is known as "memory interleaving", which requires twice as many SIMMs and effectively doubles the bandwidth.The earliest SIMM sockets were conventional push-type sockets. These were soon replaced by ZIF sockets in which the SIMM was inserted at an angle, then tilted into an upright position. To remove one, the two metal or plastic clips at each end must be pulled to the side, then the SIMM must be tilted back and pulled out (low-profile sockets reversed this convention somewhat, like SODIMMs - the modules are inserted at a "high" angle, then pushed down to become more flush with the motherboard). The earlier sockets used plastic retainer clips which were found to break, so steel clips replaced them.Some SIMMs support presence detect (PD). Connections are made to some of the pins that encode the capacity and speed of the SIMM, so that compatible equipment can detect the properties of the SIMM. PD SIMMs can be used in equipment which does not support PD; the information is ignored. Standard SIMMs can easily be converted to support PD by fitting jumpers, if the SIMMs have solder pads to do so, or by soldering wires on.".
• SIMM thumbnail SIMMs.jpg?width=300.
• SIMM wikiPageExternalLink 1000%20General%20SIMM%20Ver2(09-04).pdf.
• SIMM wikiPageID "229596".
• SIMM wikiPageRevisionID "595046146".
• SIMM hasPhotoCollection SIMM.
• SIMM subject Category:Computer_memory_form_factor.
• SIMM comment "A SIMM, or single in-line memory module, is a type of memory module containing random access memory used in computers from the early 1980s to the late 1990s. It differs from a dual in-line memory module (DIMM), the most predominant form of memory module today, in that the contacts on a SIMM are redundant on both sides of the module. SIMMs were standardised under the JEDEC JESD-21C standard.Most early PC motherboards (8088-based PCs, XTs, and early ATs) used socketed DIP chips.".
• SIMM label "SIMM".
• SIMM label "SIMM".
• SIMM label "SIMM".
• SIMM label "SIMM".
• SIMM label "SIMM".
• SIMM label "SIMM".
• SIMM label "SIMM".
• SIMM label "Single Inline Memory Module".
• SIMM label "Single Inline Memory Module".
• SIMM label "Single in-line memory module".
• SIMM sameAs SIMM.
• SIMM sameAs Single_Inline_Memory_Module.
• SIMM sameAs SIMM.
• SIMM sameAs Single_Inline_Memory_Module.
• SIMM sameAs SIMM.
• SIMM sameAs SIMM.
• SIMM sameAs SIMM.
• SIMM sameAs Single_in-line_memory_module.
• SIMM sameAs SIMM.
• SIMM sameAs SIMM.
• SIMM sameAs m.01hdzq.
• SIMM sameAs Q1063762.
• SIMM sameAs Q1063762.
• SIMM wasDerivedFrom SIMM?oldid=595046146.
• SIMM depiction SIMMs.jpg.
• SIMM isPrimaryTopicOf SIMM.